Denso RC5 Specifications Page 106
- Page / 182
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
86
4.3 Types and Functions of System Input Signals
(Compatible Mode)
The table below lists the system input signals to be used in compatible mode.
Types and Functions of System Input Signals to be Used in Compatible Mode
Application Signal name Function
Enable Auto Enables switching to Auto mode.
Motor power ON
+ operation preparation start
Turns ON the power to the motor.
CAL execution
+ operation preparation start
Executes calibration.
SP100
+ operation preparation start
Sets the speed to 100%.
Switch Ext Mode
+ operation preparation start
Switches the mode to external mode.
Program reset
+ operation preparation start
Initializes all programs on halt. Starting a
program after initialization will execute the
program from the beginning.
Start-up
Program No. select
+ program start
Executes a specified program.
Program reset
+ program No. select
+ program start
Cancels the current program and starts
executing a specified program from the
beginning.
Program execution
Robot stop Stops the robot by opening signals.
Robot stop Stops the robot by canceling signals.
Step stop Step-stops all programs by opening signals.
Stop
Instantaneous stop
Instantaneously stops all programs by opening
signals.
Error clear
Clear robot failure
+ operation preparation start
Clears an error.
Program interrupt
Interrupt skip
Interrupts the execution of the current step
and starts the next step.
Continue start
Continue start
+ program start
Executes continue start.
Caution: Two or more signal names listed in the signal name field
indicate that they should be used in combination.
- INTERFACE MANUAL 1
- Preface 3
- How this book is organized 5
- 3. Installation Precautions 9
- SAFETY PRECAUTIONS 11
- Warning 13
- Contents 17
- RC5 - VSE 6 B A - P 21
- 2.3 Setting the parameter 23
- /HM-E series 24
- <Front> 25
- [ 1 ] Specifications 27
- [ 2 ] Outer Dimensions 29
- Location of IPM boards 30
- (VM-D, VS-E, HS-E, and HM-E) 32
- (VS-D, VC-E, H 33
- -D, and XYC-D) 33
- 2.2 Switching between Modes 34
- 2.3.1 Standard Mode 42
- 2.3.2 Compatible Mode 43
- 2.4.4 User Input Commands 44
- 2.4.5 User Output Commands 45
- Chapter 3 46
- (5) OFF condition 47
- 3.2.2 Auto Mode (Output) 48
- 3.2.4 Servo ON (Output) 50
- 3.2.6 Normal CPU (Output) 52
- (4) ON condition 54
- 3.2.11 SS mode (Output) 56
- 3.4.1 Enable Auto (Input) 59
- 3.4.2 Robot Stop (Input) 60
- (2) Terminal 61
- Halt OFF (open) 62
- Dedicated to Standard Mode 65
- [ 2 ] Strobe Signal (Input) 69
- [ 4 ] Status Area 71
- 3.5.3 I/O Commands Details 72
- (2) Format 73
- (3) Description 73
- 3.5.3.4 Error Read (0100) 77
- Type I Variable Read (0110) 79
- 3.5.3.9 I/O Write (1001) 83
- 3.5.3.10 I/O Read (1010) 84
- (1) Equipment setup example 85
- Chapter 4 89
- 4.2.2 Auto Mode (Output) 91
- 4.2.3 Servo ON (Output) 92
- ⋅ CAL EXECUTION and OPERATION 93
- 4.2.6 Teaching (Output) 95
- 4.2.10 Normal CPU (Output) 99
- (1) Function 100
- (2) Terminal number 100
- (3) Usage 100
- (4) ON conditions 100
- (5) OFF conditions 100
- (1) Function 101
- 4.2.14 Error No. (Output) 103
- 4.2.16 SS mode (Output) 104
- (4) Contact 105
- (Compatible Mode) 106
- 4.4.1 Enable Auto (Input) 107
- The mode is switched to 109
- external mode 109
- (2) Terminal numbers 110
- 4.4.4 Program Start (Input) 112
- 1-cycle Operation 112
- Program Start Operation-2 113
- Program Start Operation-3 114
- 1→T2→T3 in the figure 116
- 4.4.5 Program Reset (Input) 118
- 4.4.6 Robot Stop (Input) 120
- ON (shorted) 122
- 50 ms. or more required 122
- Instantaneous 122
- (e.g., conveyor) 126
- (2) Outline of procedure 127
- Operation start area check 128
- Operation position 1 ON 128
- Automatic operation 129
- Operation end 129
- Executing single-cycle 129
- [ 1 ] From the teach pendant 131
- [ 2 ] In WINCAPSII 132
- Parameter details 134
- User I/O signal lines 137
- Chapter 5 138
- 5.2.4.1 Standard type 152
- Check point (2) 156
- Chapter 6 158
- 6.2.4.1 Standard type 172
- Check point (1) 176
- Chapter 7 I/O Wiring 178
- : 230 VAC, phase R 180
- B: 230 VAC, phase S 180
- C: Not used 180
- D: Ground 180
- RC5 CONTROLLER 181
Related products and manuals for Robotics Denso RC5
Robotics Denso RC5 Specifications
(138 pages)
(138 pages)
© 2020, manymanuals.com. All rights reserved. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals