Denso RC5 Specifications Page 110
- Page / 182
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
90
4.4.3 Program No. Select (Input)
(1) Function
The program number to be executed can be specified from the external
device by inputting this signal.
(2) Terminal numbers
No.11 to No.18 of connector CN8.
(3) Input conditions and operation
This signal is executable only in the external mode. In other modes, an
error (ERROR21E2, 21E4, 21E6) will be displayed, and the terminal
motor power will be turned OFF.
As shown in the table given on the next page, the program No. select
signal is made up of eight bits of 2
0
to 2
6
and the parity bit.
Input a decimal program number by converting it into binary 2
0
to 2
6
and
parity bit.
"Short" represents the bit value = 1, "open" represents the bit value = 0,
and the parity bit is odd parity.
As shown below, input the program No. select signal before the program
start signal (1 msec. or more), and hold the state until the robot starts to
operate. If this condition is not met, ERROR2031 or ERROR2033 will be
displayed, the power to the motor will be turned OFF.
Robot status
Wait for start
or preceding cycle
Single-cycle operation
1 ms. or more required
Program ON (shorted)
start (input) OFF (open)
Program No. select signal
2
0
to 2
6
ON (shorted)
Parity OFF (open)
Program No. Select Signal
Input 1 or 0 as the parity bit so that the total of 1’s existing in the eight bits
of 2
0
to 2
6
and the parity bit will be odd.
Example: When the program number is 15, the bit status of 2
0
to 2
6
is
(001111), and the total number of 1s is four, an even number.
Set 1 as the parity bit to make the total number of 1s five, an
odd number.
Caution The bit value =1 represents short, and the bit value =0
represents open.
The program numbers executable from the external device
are limited to Pro0 to Pro127.
- INTERFACE MANUAL 1
- Preface 3
- How this book is organized 5
- 3. Installation Precautions 9
- SAFETY PRECAUTIONS 11
- Warning 13
- Contents 17
- RC5 - VSE 6 B A - P 21
- 2.3 Setting the parameter 23
- /HM-E series 24
- <Front> 25
- [ 1 ] Specifications 27
- [ 2 ] Outer Dimensions 29
- Location of IPM boards 30
- (VM-D, VS-E, HS-E, and HM-E) 32
- (VS-D, VC-E, H 33
- -D, and XYC-D) 33
- 2.2 Switching between Modes 34
- 2.3.1 Standard Mode 42
- 2.3.2 Compatible Mode 43
- 2.4.4 User Input Commands 44
- 2.4.5 User Output Commands 45
- Chapter 3 46
- (5) OFF condition 47
- 3.2.2 Auto Mode (Output) 48
- 3.2.4 Servo ON (Output) 50
- 3.2.6 Normal CPU (Output) 52
- (4) ON condition 54
- 3.2.11 SS mode (Output) 56
- 3.4.1 Enable Auto (Input) 59
- 3.4.2 Robot Stop (Input) 60
- (2) Terminal 61
- Halt OFF (open) 62
- Dedicated to Standard Mode 65
- [ 2 ] Strobe Signal (Input) 69
- [ 4 ] Status Area 71
- 3.5.3 I/O Commands Details 72
- (2) Format 73
- (3) Description 73
- 3.5.3.4 Error Read (0100) 77
- Type I Variable Read (0110) 79
- 3.5.3.9 I/O Write (1001) 83
- 3.5.3.10 I/O Read (1010) 84
- (1) Equipment setup example 85
- Chapter 4 89
- 4.2.2 Auto Mode (Output) 91
- 4.2.3 Servo ON (Output) 92
- ⋅ CAL EXECUTION and OPERATION 93
- 4.2.6 Teaching (Output) 95
- 4.2.10 Normal CPU (Output) 99
- (1) Function 100
- (2) Terminal number 100
- (3) Usage 100
- (4) ON conditions 100
- (5) OFF conditions 100
- (1) Function 101
- 4.2.14 Error No. (Output) 103
- 4.2.16 SS mode (Output) 104
- (4) Contact 105
- (Compatible Mode) 106
- 4.4.1 Enable Auto (Input) 107
- The mode is switched to 109
- external mode 109
- (2) Terminal numbers 110
- 4.4.4 Program Start (Input) 112
- 1-cycle Operation 112
- Program Start Operation-2 113
- Program Start Operation-3 114
- 1→T2→T3 in the figure 116
- 4.4.5 Program Reset (Input) 118
- 4.4.6 Robot Stop (Input) 120
- ON (shorted) 122
- 50 ms. or more required 122
- Instantaneous 122
- (e.g., conveyor) 126
- (2) Outline of procedure 127
- Operation start area check 128
- Operation position 1 ON 128
- Automatic operation 129
- Operation end 129
- Executing single-cycle 129
- [ 1 ] From the teach pendant 131
- [ 2 ] In WINCAPSII 132
- Parameter details 134
- User I/O signal lines 137
- Chapter 5 138
- 5.2.4.1 Standard type 152
- Check point (2) 156
- Chapter 6 158
- 6.2.4.1 Standard type 172
- Check point (1) 176
- Chapter 7 I/O Wiring 178
- : 230 VAC, phase R 180
- B: 230 VAC, phase S 180
- C: Not used 180
- D: Ground 180
- RC5 CONTROLLER 181
Related products and manuals for Robotics Denso RC5
Robotics Denso RC5 Specifications
(138 pages)
(138 pages)
© 2020, manymanuals.com. All rights reserved. | 2.246 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals