Denso RC5 Specifications Page 127
- Page / 182
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
107
Function Example of Equipment Operating Panel
Classification Part Application
Display Display
Displays messages, such as ROBOT PREPARATION
OK.
Automatic operation
indicator lamp
⋅ Lights during automatic operation.
⋅ Not illuminated when the robot is not in automatic
operation.
Robot external mode
indicator lamp
⋅ Lights when the robot is in external mode.
⋅ Turned OFF when the robot is not in external mode.
Lamp
Operation OK indicator
lamp
⋅ Lights when the Enable Auto signal is ON.
⋅ Turned OFF when the Enable Auto signal is OFF.
Robot operation button Starts the robot preparation.
Automatic start button Starts the operation of the equipment.
Cycle stop button
Stops the equipment after a cycle of operations is
completed.
Switch
Operation/Adjustment
selector switch
Automatic operation of the robot possible when
OPERATION is selected.
Manual operation or teach check of the robot possible
when ADJUSTMENT is selected.
Note: Actual equipment requires emergency stop, interlock and other functions. However,
described here are only necessary functions and others are omitted.
(2) Outline of procedure
Described below is the outline of the procedure when using the equipment,
as shown on the previous page.
Follow steps to .
Operation preparation start
Setting the MOTOR POWER ON, CAL EXECUTION, SP100 and
SWITCH EXT MODE bits, brings the robot into the External Auto mode.
This operation will be completed when the EXTERNAL MODE output
signal is turned ON.
Automatic operation
Start the program by which the robot starts from the operation origin,
performs operations, and returns to the operation origin.
Operation end
Terminate the day’s operations with a cycle stop, and turn OFF the power.
(3) Start and stop procedure and system I/O signals
The following pages show the relationship between the system I/O signals
for start and stop, worker’s operation, display on the equipment operation
panel, PLC proceeding, and robot motion.
- INTERFACE MANUAL 1
- Preface 3
- How this book is organized 5
- 3. Installation Precautions 9
- SAFETY PRECAUTIONS 11
- Warning 13
- Contents 17
- RC5 - VSE 6 B A - P 21
- 2.3 Setting the parameter 23
- /HM-E series 24
- <Front> 25
- [ 1 ] Specifications 27
- [ 2 ] Outer Dimensions 29
- Location of IPM boards 30
- (VM-D, VS-E, HS-E, and HM-E) 32
- (VS-D, VC-E, H 33
- -D, and XYC-D) 33
- 2.2 Switching between Modes 34
- 2.3.1 Standard Mode 42
- 2.3.2 Compatible Mode 43
- 2.4.4 User Input Commands 44
- 2.4.5 User Output Commands 45
- Chapter 3 46
- (5) OFF condition 47
- 3.2.2 Auto Mode (Output) 48
- 3.2.4 Servo ON (Output) 50
- 3.2.6 Normal CPU (Output) 52
- (4) ON condition 54
- 3.2.11 SS mode (Output) 56
- 3.4.1 Enable Auto (Input) 59
- 3.4.2 Robot Stop (Input) 60
- (2) Terminal 61
- Halt OFF (open) 62
- Dedicated to Standard Mode 65
- [ 2 ] Strobe Signal (Input) 69
- [ 4 ] Status Area 71
- 3.5.3 I/O Commands Details 72
- (2) Format 73
- (3) Description 73
- 3.5.3.4 Error Read (0100) 77
- Type I Variable Read (0110) 79
- 3.5.3.9 I/O Write (1001) 83
- 3.5.3.10 I/O Read (1010) 84
- (1) Equipment setup example 85
- Chapter 4 89
- 4.2.2 Auto Mode (Output) 91
- 4.2.3 Servo ON (Output) 92
- ⋅ CAL EXECUTION and OPERATION 93
- 4.2.6 Teaching (Output) 95
- 4.2.10 Normal CPU (Output) 99
- (1) Function 100
- (2) Terminal number 100
- (3) Usage 100
- (4) ON conditions 100
- (5) OFF conditions 100
- (1) Function 101
- 4.2.14 Error No. (Output) 103
- 4.2.16 SS mode (Output) 104
- (4) Contact 105
- (Compatible Mode) 106
- 4.4.1 Enable Auto (Input) 107
- The mode is switched to 109
- external mode 109
- (2) Terminal numbers 110
- 4.4.4 Program Start (Input) 112
- 1-cycle Operation 112
- Program Start Operation-2 113
- Program Start Operation-3 114
- 1→T2→T3 in the figure 116
- 4.4.5 Program Reset (Input) 118
- 4.4.6 Robot Stop (Input) 120
- ON (shorted) 122
- 50 ms. or more required 122
- Instantaneous 122
- (e.g., conveyor) 126
- (2) Outline of procedure 127
- Operation start area check 128
- Operation position 1 ON 128
- Automatic operation 129
- Operation end 129
- Executing single-cycle 129
- [ 1 ] From the teach pendant 131
- [ 2 ] In WINCAPSII 132
- Parameter details 134
- User I/O signal lines 137
- Chapter 5 138
- 5.2.4.1 Standard type 152
- Check point (2) 156
- Chapter 6 158
- 6.2.4.1 Standard type 172
- Check point (1) 176
- Chapter 7 I/O Wiring 178
- : 230 VAC, phase R 180
- B: 230 VAC, phase S 180
- C: Not used 180
- D: Ground 180
- RC5 CONTROLLER 181
Related products and manuals for Robotics Denso RC5
Robotics Denso RC5 Specifications
(138 pages)
(138 pages)
© 2020, manymanuals.com. All rights reserved. | 1.590 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals